A revolutionary product, S-1300 Pene-Krete is a non-hazardous penetrating sealer for use on all concrete and masonry substrates.
S-1300 Pene-Krete reacts with alkali and free lime in common cement and creates an internal crystal-like shield, increasing the strength of new and existing concrete and masonry, and reducing moisture vapor transmission.
It protects surfaces from freeze/thaw damage, reduces dusting of concrete, and increases coating life by as much as 300%. Surface preparation must be sufficient to allow Pene-Krete to penetrate the surface. Spray application only.S-1300 Pene-Krete is the key component to coating success and is required for use in all Super-Krete systems.
Coverage Rate
Approximately 300 sf/gallon
Packaging
Gallon Bottle
5 Gallon Pails
55 Gallon Drum
1 Pallet (36 pails)
275 Gallon Tote
A non-hazardous liquid additive formulated to create a chemical reaction within portland cement-based products. The addition of Pene-Krete Additive enhances the concrete’s natural hydration process by prolonging the hydration of the cementing materials and increasing workability.
Packaging
Gallon Bottle
5 Gallon Pails
55 Gallon Drum
1 Pallet (36 pails)
275 Gallon Tote
VaporSolve® 100 is a low viscosity, hydrophobic resin system that cures on wet or damp concrete. It is used as a single coat remediation system or a top coat over VaporSolve® Primer.
Colors & Finishes
White
Wheat
Delta Fog
Options
Available Formulas: Fast Cure
Packaging
Pre-Measured Kits:
1 Gallon
3 Gallons
VaporSolve® FC (Fresh Concrete) is a specially formulated water-based epoxy for use over freshly poured concrete to act as a high-performance concrete curing compound and as a primer under VaporSolve® 100 material. VaporSolve FC has been formulated with very low viscosity and surface tension to ensure excellent substrate wetting, penetration and adhesion.
Its unique chemistry gives it excellent affinity for the moist, alkaline conditions found in freshly poured concrete. Additionally, its ability to hold moisture in fresh concrete far exceeds the capabilities of conventional curing compounds and results in better hydrated and stronger concrete. When applied as a system, VaporSolve FC and VaporSolve 100 prevent moisture migration through the concrete slab and allow the application of moisture sensitive flooring after 12 hours. The use of this unique system eliminates the need for a sub-slab vapor retarder as well as the need for shot-blasting prior to the application of subsequent flooring or coating.
Packaging
Pre-Measured Kits:
3/4 Gallon
2 Gallons
SK-VaporSolve® Fresh Concrete Product Datasheet
VaporSolve® Joint Filler is a non-shrinking, semi-rigid epoxy paste used for filling joints and cracks in concrete that will recieve VaporSolve® Systems. It resists long term moisture and alkalinity.
Options
Available Formulas: Fast Cure
Packaging
Pre-Measured Kits
3/4 Gallons
1 1/2 Gallons
3 Gallons
SK-VaporSolve® Joint Filler Product Datasheet
VaporSolve® Joint Filler Fast Cure Part B
VaporSolve® Primer is a water-based epoxy material with deep penetration and adhesion to concrete. It has superior performance to 100% solids materials over contaminated concrete. This product eliminates or greatly reduces concrete outgassing.
Colors & Finishes
Clear
White
Wheat
Delta Fog
Options
Available Formulas: Fast Cure
Packaging
Pre-Measured Kits
3/4 Gallon
3 Gallons
VaporSolve® Tie Coat is a two component, fast drying water-based epoxy formulated for use over non-porous surfaces such as APF’s VaporSolve® Moisture Remediation Systems. It insures the adhesion of subsequently applied cementitious overlays. VaporSolve® Tie Coat adheres tenaciously to hard glossy surfaces and provides an excellent bonding surface for the overlay. It dries in 30-60 minutes depending upon job conditions and is safe and easy to use.
Colors & Finishes
Off White
Packaging
Pre-Measured Kits:
2 Gallons
10 Gallons
SK-VaporSolve® Tie Coat Product Datasheet